Hi all,
Does anybody know if, when using the Range definition in Custom Axis Configuration, I can assign a different rotorbrake code depending on whether I move the Axis clockwise or counterclockwise through a set Range. I'm trying to control the brightness of a VC display that I can only control with 2 rotorbrake codes; one to increase and one to decrease the brightness. The actual control is a rotary knob. I recall that in FSUIPC I was able to differentiate between going up or down a set range. It wasn't pretty, but I managed to simulate turning the brightness knob this way.
Thanks!
Current SPAD.neXt Release: 0.9.12.123
This forum has closed. Please join our Discord Community.
SPAD.neXt online services are no longer available for SPAD.neXt Versions < 0.9.11.5
Custom Axis configuration and Rotorbrakes again
Custom Axis configuration and Rotorbrakes again
Saitek HW: ProFlight Yoke (upgraded with springs and a LeoBodnar JC), 2 TQs, 2 RPs, MP, SP
Other HW: MFG rudderpedals, Logitech Extreme 3D Joystick, DIY A320 glareshield (WIP; 3 BBI32s and 2 PACLED64s)
Other HW: MFG rudderpedals, Logitech Extreme 3D Joystick, DIY A320 glareshield (WIP; 3 BBI32s and 2 PACLED64s)
- Oz Flyer
- Betatester
- Posts: 741
- Joined: 23 Sep 2015, 10:10
- Location: YMMB, Melbourne, Australia
- Contact:
- Status: Offline
Re: Custom Axis configuration and Rotorbrakes again
Can you set one to increase and the other to decrease at the same time?
turning clockwise
So that you have one going say "A" = 0 to 255 while the other is "B" going 255 to 0
turning counterclockwise
"A" = 255 to 0 and "B" = 0 to 255
Two events on one knob.
turning clockwise
So that you have one going say "A" = 0 to 255 while the other is "B" going 255 to 0
turning counterclockwise
"A" = 255 to 0 and "B" = 0 to 255
Two events on one knob.
David
OZ Flyer
Near YMMB
40+ year of Flight Siming.
Sim: subLOGIC/Microsoft Flight Sim's/DTG FSX, Microsoft Flight, DTG Filght School/FSW/Train Sim/TSW, ETS2 & ATS.
Hardware: Logitech, Saitek, Arduino 2560's & Leo's, BBI-32, PAC LED.
OZ Flyer
Near YMMB
40+ year of Flight Siming.
Sim: subLOGIC/Microsoft Flight Sim's/DTG FSX, Microsoft Flight, DTG Filght School/FSW/Train Sim/TSW, ETS2 & ATS.
Hardware: Logitech, Saitek, Arduino 2560's & Leo's, BBI-32, PAC LED.
Re: Custom Axis configuration and Rotorbrakes again
Hi David,
Thanks, I have successfully done this with FSUIPC. I was wondering if this method works with SPADNEXT as well...using the Custom Axis configuration feature..will it differentiate between moving through a range clockwise and anti clockwise?
Thanks, I have successfully done this with FSUIPC. I was wondering if this method works with SPADNEXT as well...using the Custom Axis configuration feature..will it differentiate between moving through a range clockwise and anti clockwise?
Saitek HW: ProFlight Yoke (upgraded with springs and a LeoBodnar JC), 2 TQs, 2 RPs, MP, SP
Other HW: MFG rudderpedals, Logitech Extreme 3D Joystick, DIY A320 glareshield (WIP; 3 BBI32s and 2 PACLED64s)
Other HW: MFG rudderpedals, Logitech Extreme 3D Joystick, DIY A320 glareshield (WIP; 3 BBI32s and 2 PACLED64s)
- Oz Flyer
- Betatester
- Posts: 741
- Joined: 23 Sep 2015, 10:10
- Location: YMMB, Melbourne, Australia
- Contact:
- Status: Offline
Re: Custom Axis configuration and Rotorbrakes again
try is and report back and let us know
If not tell us what it did or did not do and we can work from there.
If not tell us what it did or did not do and we can work from there.
David
OZ Flyer
Near YMMB
40+ year of Flight Siming.
Sim: subLOGIC/Microsoft Flight Sim's/DTG FSX, Microsoft Flight, DTG Filght School/FSW/Train Sim/TSW, ETS2 & ATS.
Hardware: Logitech, Saitek, Arduino 2560's & Leo's, BBI-32, PAC LED.
OZ Flyer
Near YMMB
40+ year of Flight Siming.
Sim: subLOGIC/Microsoft Flight Sim's/DTG FSX, Microsoft Flight, DTG Filght School/FSW/Train Sim/TSW, ETS2 & ATS.
Hardware: Logitech, Saitek, Arduino 2560's & Leo's, BBI-32, PAC LED.