Still working on the backlog of tickets. Please bear with me. If you have a licence-ticket that needs urgent attention update it to push it up.

Search found 47 matches

by krono
Yesterday, 07:19
Forum: General
Topic: Advice of hardware power
Replies: 9
Views: 145

Re: Advice of hardware power

Hi Just to reaffirm. I have been using the same hub that Hazza left a link for {https://www.pbtech.co.nz/product/USBMBE1002/mbeat-USB-M13HUB-13-Port-USB20-Hub-with-individual) for aproximately four years with no hassles. Its a good little unit running yoke, radio ,switch panel, autopilot panel, 1 Fi...
by krono
13 Oct 2019, 03:59
Forum: Hardware
Topic: PacLed64 and DCS
Replies: 2
Views: 203

Re: PacLed64 and DCS

Thanks for the answer Connex

Ken
by krono
12 Oct 2019, 05:54
Forum: Hardware
Topic: PacLed64 and DCS
Replies: 2
Views: 203

PacLed64 and DCS

Hi Connex I know that all further implementation of DCS has been stopped but I can remember that the DCS module was at the stage that it could read from DCS but not send information to it. Since this is the case is there the opportunity to be able to use your DCS module to simply read that informati...
by krono
02 Jul 2019, 15:55
Forum: General
Topic: problems with placled64 LED outputs
Replies: 11
Views: 1369

Re: problems with placled64 LED outputs

Hi toppe If you look at the lines printed above then when LVar:Battery1Switch == 0 or Simconnect:InnerMarker ==0 The Led will go to Off. On the event plate you can see that is Labeled off. ie Led turns off. When LVar:Battery1Switch == 1 && Simconnect:InnerMarker == 1 When both are on the led goes to...
by krono
02 Jul 2019, 04:35
Forum: General
Topic: problems with placled64 LED outputs
Replies: 11
Views: 1369

Re: problems with placled64 LED outputs

Hi Have you remembered to have an option programed into spad to turn the led off and not just onjuast the same as a switch. A quick example would be Plate 18 (S17 Inner Maker) //This is the name of the plate on the Pacled64 Event LVar:Battery1Switch == 0 Simconnect:InnerMarker == 0 //Here if the mai...
by krono
24 Jun 2019, 12:21
Forum: General
Topic: Help with rotary switch
Replies: 16
Views: 835

Re: Help with rotary switch

Hi If you are using a rotary encoder switch then this is a fairly easy situation.I use these on my gyro compass AP heading. Anti clockwise to decrement the value and clockwise to increment the value and the central push switch to change the value of the incremented value or in your case the value ty...
by krono
25 Apr 2019, 16:09
Forum: Hardware
Topic: Saitek Throttle Mod
Replies: 2
Views: 542

Re: Saitek Throttle Mod

Well put together video. I also use the bodnar boards in conjunction with PacLed64 and the same as Daz a 3d printer it is a win win situation. I think it is the original pots in the Saitek unit that will still give you trouble as I find they wear very quickly.

Ken
by krono
08 Jan 2019, 05:49
Forum: General
Topic: Pololu Servo Controller?
Replies: 11
Views: 921

Re: Pololu Servo Controller?

Hi
Its nice to see Arduino being discussed again :-)
by krono
24 Oct 2018, 05:34
Forum: General
Topic: Rudder Slip Feedback
Replies: 7
Views: 803

Re: Rudder Slip Feedback

David In the simshaker module you can specify that you are using a stereo input. I use a 4 legged chair rather than an office chair on wheels because of the flight simming which means there is a separation between the 2 buttkickers as they are mounted on the two rear legs, I find that it gives just ...
by krono
23 Oct 2018, 07:33
Forum: General
Topic: Rudder Slip Feedback
Replies: 7
Views: 803

Re: Rudder Slip Feedback

Hi
I am glad you are enjoying it. As i said earlier I use 2 on my chair through an onboard soundcard in stereo to a normal amplifier on the front 2 channels. I have blown 2 of the buttkicker amps in the past and find that a standard amp with Andres simshaker module a lot better.

Ken