Hi
Mozilla Firefox is not allowing access to your site at the moment due to.....SEC_ERROR_REVOKED_CERTIFICATE.
I have had to go back to internet explorer to gain access here. For your info this only started to happen this afternoon you were fine this morning. All my other saved sites are fine.
Ken
Current SPAD.neXt Release: 0.9.12.123
This forum has closed. Please join our Discord Community.
SPAD.neXt online services are no longer available for SPAD.neXt Versions < 0.9.11.5
Search found 52 matches
- 28 Jan 2017, 09:19
- Forum: Bugs / Problems
- Topic: certificate revoked
- Replies: 4
- Views: 2742
- 22 Jan 2017, 00:39
- Forum: General
- Topic: Sending CH Yoke Button To Networked PC
- Replies: 12
- Views: 8917
Re: Sending CH Yoke Button To Networked PC
Hi
Not sure if the same but I run Pilot2ATC and spadnext with all controls on networked pC on P3d. When all on networked machine simply program yoke button in Pilot2atc setup. Saves a lot of hassles.
Ken
Not sure if the same but I run Pilot2ATC and spadnext with all controls on networked pC on P3d. When all on networked machine simply program yoke button in Pilot2atc setup. Saves a lot of hassles.
Ken
- 26 Dec 2016, 02:36
- Forum: Hardware
- Topic: Custom FIP
- Replies: 15
- Views: 10290
Re: Custom FIP
Hi
Looking forward to the outcome
Ken
Looking forward to the outcome
Ken
- 26 Dec 2016, 02:28
- Forum: Hardware
- Topic: Arduino controler
- Replies: 102
- Views: 80357
Re: Arduino controler
Good to see you are enjoying the arduino. They are pretty cool, I was lucky to get a PacLed64 under the tree so am looking at that at the moment.
Ken
Ken
- 09 Dec 2016, 13:25
- Forum: General
- Topic: Trial Version-Combat Rudder Pedals not working
- Replies: 3
- Views: 2248
Re: Trial Version-Combat Rudder Pedals not working
Hi
You need to program Rudder as a "Custom Axis Configeration"
Event "Axis change" Axis Control Axis_Rudder_SET(axis normalized) Priority "0"
Range definition "no" Rescale value "no"
Target "AXIS_RUDDUR_SET"
value to set "0"
use axis value "on"
use raw value "off"
invert axis "off"
Ken
You need to program Rudder as a "Custom Axis Configeration"
Event "Axis change" Axis Control Axis_Rudder_SET(axis normalized) Priority "0"
Range definition "no" Rescale value "no"
Target "AXIS_RUDDUR_SET"
value to set "0"
use axis value "on"
use raw value "off"
invert axis "off"
Ken
- 26 Nov 2016, 01:35
- Forum: Hardware
- Topic: A button, switch, & knob box
- Replies: 7
- Views: 9704
Re: A button, switch, & knob box
Looking good
Keep us all posted
Ken
Keep us all posted
Ken
- 26 Nov 2016, 01:31
- Forum: Hardware
- Topic: Flash Arduino as HID device
- Replies: 3
- Views: 3812
Re: Flash Arduino as HID device
Hi
Just for an update...
I am keeping the arduino as is rather than flashing it and have ordered an Ultimarc PacLed64 WHOOt.....WHOOt.
I am looking forward to making this unit in conjunction with a Derek Speares board for a BIP and switch panel combined.
Ken
Just for an update...
I am keeping the arduino as is rather than flashing it and have ordered an Ultimarc PacLed64 WHOOt.....WHOOt.
I am looking forward to making this unit in conjunction with a Derek Speares board for a BIP and switch panel combined.
Ken
- 23 Nov 2016, 02:31
- Forum: Hardware
- Topic: Flash Arduino as HID device
- Replies: 3
- Views: 3812
Re: Flash Arduino as HID device
Ok thats no worries I am thinking of flashing to a compatible board that you already do. Its a round about way but should work albiet a bit fiddly to set up.
Ken
Ken
- 22 Nov 2016, 04:57
- Forum: Hardware
- Topic: Flash Arduino as HID device
- Replies: 3
- Views: 3812
Flash Arduino as HID device
Hi I have been looking at the arduino mega for a while. If I flash an Arduino to a HID device keyboard with HoodLoader do you think Spad.next would then be able to see it to use as a bip type controller. I will probably try this in the next couple of days to see how it goes. I know I could clone it ...
- 14 Sep 2016, 09:58
- Forum: Bugs / Problems
- Topic: Altitude on saitek multi panel
- Replies: 1
- Views: 1833
Re: Altitude on saitek multi panel
I have used an FSCUIP command for now. I was hoping to use either LVAR or simmconnect but both of these overloaded the multipanel with too much information so that the lights and display could not keep up.
The panel for the A2A commanche STC on the multipanel should now be online
The panel for the A2A commanche STC on the multipanel should now be online