Current SPAD.neXt Release: 0.9.12.123
This forum has closed. Please join our Discord Community.
SPAD.neXt online services are no longer available for SPAD.neXt Versions < 0.9.11.5
Search found 29 matches
- 28 Oct 2020, 16:25
- Forum: General
- Topic: throttle reversal in fs2020
- Replies: 2
- Views: 2705
throttle reversal in fs2020
I am not sure if this is a problem with SPAD or not. On the Saitek throttle quadrant, the axis is reversed even when I tick the reverse slot in MSFS. I have reconfigured the controls within SPAD and keep getting the same problem. Also noted is that the throttle stops at 90%. If the push the saitek l...
- 20 Dec 2018, 18:30
- Forum: Bugs / Problems
- Topic: Saitek Multi Panel with 0.9.6.5.2. Trimming wheel problem
- Replies: 7
- Views: 4165
Re: Saitek Multi Panel with 0.9.6.5.2. Trimming wheel problem
This has to do with windows recognition. When you turn on your computer turn the wheel until you hear two beeps. This solved the problem for me. Someone named "Cowboy" in the forum told me this. Good Luck.
BW
BW
- 29 Aug 2018, 17:15
- Forum: Bugs / Problems
- Topic: Lvar Bridge Plugin
- Replies: 0
- Views: 4387
Lvar Bridge Plugin
I have posted a ticket on this problem and have asked about it in the complete edition. I know you said you had a backlog. I left a follow up question on the complete edition but did not hear back...Are you viewing responses in the complete edition? I am not sure how to proceed so I am going to post...
- 13 Jun 2017, 19:42
- Forum: Bugs / Problems
- Topic: Cessna Trim Wheel
- Replies: 3
- Views: 3241
Re: Cessna Trim Wheel
Seems that I was in error. Trim Wheel now not functioning and further after I deleted the config and then reinstalled the same config, it caused a computer lock and then blue screen. I believe I have bad hardware and plan not to use this trim control at all. I have removed it from my setup.
- 11 Jun 2017, 20:58
- Forum: Bugs / Problems
- Topic: Cessna Trim Wheel
- Replies: 3
- Views: 3241
Cessna Trim Wheel
Thanks for the update that fixed the problem with the Cessna Trim Wheel. Now working smoothly and correctly.
BW
BW
- 08 Feb 2017, 18:24
- Forum: Bugs / Problems
- Topic: FIPS LOST LABEL CONFIG
- Replies: 3
- Views: 2716
FIPS LOST LABEL CONFIG
I HAD A PROBLEM WITH MY COMPUTER AND SPAD WAS NOT USED FOR ABOUT A WEEK. WHEN I PLUGGED MY CORDS BACK IN ALL THE PANELS WORKED BUT THE FIPS WAS NOT FUNCTIONING. IT STATED THAT I NEEDED TO LOAD ALL THE FIP SCREENS. I DID THIS, BUT MY LABELS WERE MISSING. ALSO WHEN I SWITCH TO DIFFERENT PROFILE. I HAV...
- 20 Jan 2017, 03:34
- Forum: Bugs / Problems
- Topic: multi panel AP buttons not responding
- Replies: 3
- Views: 2607
Re: multi panel AP buttons not responding
Working OK now...somehow all configurations had to be reprogrammed. My apologies
Blackwolf
Blackwolf
- 19 Jan 2017, 23:59
- Forum: Bugs / Problems
- Topic: multi panel AP buttons not responding
- Replies: 3
- Views: 2607
multi panel AP buttons not responding
Suddenly all the auto pilot buttons do remain at 0 when turning the knob. The one exception is the Altitude setting does increase and decrease, but this is the only functioning button. These have worked previously. Could this be related to an update??
Blackwolf
Blackwolf
- 28 Dec 2016, 04:26
- Forum: Bugs / Problems
- Topic: Axis problem on X52 Pro
- Replies: 1
- Views: 1780
Axis problem on X52 Pro
I have the Saitek yoke andX52 pro. The x and y axis are inoperative on the x52. The axis work on the yoke but I cannot use the x52 to fly. Is there a conflict because I have the yoke installed?? I also have other joysticks I have the same problem with all of them. The X and Y axis only work with the...
- 17 Dec 2016, 22:11
- Forum: Bugs / Problems
- Topic: congiguring pushback right and left
- Replies: 3
- Views: 2283
Re: congiguring pushback right and left
Right and left pushback working as you indicated. When I first initiated the command in the sim, the flaps came down again which I knew was due to the controller being enabled. Sure enough it was so I turned it off again. My cycle views button was not working which I have assigned to the D key so th...